DR：岛津（SHIMADZU） RADspeed fit故障报错

2026-03-0549 阅读故障报错

Error Code List

Error Code	Meaning
L8	The examination room door is open.
H1	When conducting radiography under the set X-ray conditions, the heat content exceeded the allowable heat content of the X-ray tube unit.
H2	The heat content has exceeded the maximum heat capacity of the X-ray tube unit.
H4	The thermal circuit of the X-ray tube unit has activated.
F90	The temperature of main inverter IGBT is higher than 100 degC.
F64	Radiography switch input error
F65	Radiography preparation switch input error
E	CPU memory battery replacement time
EEE	CPU memory battery expiration

F03	-15V power supply control circuit fault
F11	The measured tube voltage is at least 30 kV higher than the setting value.
F12	The measured tube voltage is at least 70% lower than the setting value.
F13	The measured tube voltage is approx. 10 kV or lower.
F14	The X-ray tube has discharged. (3rd discharge)
F17 *	The X-ray tube has discharged. (1st discharge)
F18 *	The X-ray tube has discharged. (2nd discharge)
F19	The tube voltage on either anode or cathode side is higher than 90 kV.
F21	The measured tube current is at least 50 mA higher than the setting value.
F22	The measured tube current is at least 50% lower than the setting value.
F23	The measured tube current is less than approx. 8 mA.
F2F	The measured tube current is higher than approx. 1000 mA.
F31	The measured filament current is at least 120% higher than the setting value.
F32	The measured filament current is at least 80% lower than the setting value.
F33	The measured filament current is approx. 1 A or lower.
F34	The measured filament current is higher than the maximum focal spot current.
F41	The measured capacitor voltage on the positive (+) side is higher than approx. 367 V.
F42	The measured capacitor voltage on the positive (+) side is lower than approx. 235 V.
F43	The measured capacitor voltage on the positive (+) side is lower than approx. 20 V.
F44	The measured capacitor voltage on the negative (-) side is higher than approx. 367 V.
F45	The measured capacitor voltage on the negative (-) side is lower than approx. 235 V.
F46	The measured capacitor voltage on the negative (-) side is lower than approx. 20 V.
F55	The measured capacitor voltage on the positive (+) side is at least 30 V higher than that on the negative (-) side.
F56	The measured capacitor voltage on the negative (-) side is at least 30 V higher than that on the positive (+) side.
F61	Starter fault (The starter does not activate normally at the start ofexposure. Or, the starter drive does not finish normally at the end of exposure.)

F62	Bucky fault (No confirmation signal from the Bucky)
F6E	Exposure control circuit fault
F6F	Exposure control circuit fault
F6H	Exposure control circuit fault. Exposure interruption (no checking signal from FPD)
F71	Dose area product communication timeout error
F72	Dosimeter communication error
F73	Dosimeter failure
F90	IGBT device is in high temperature.
F91	No additional filter is inserted though the additional filter setup has been done in the system.
F92	An additional filter is inserted though the additional filter setup has not been done in the system.
F93	The combination of the software installed (for emerging countries or for North America) and the software type memorized to EEPROM is notcorrect.Update to the software of correct combination or initialize the system.
F2a	Tube voltage feedback circuit fault
F1a	Tube voltage feedback circuit fault

F68	FPD fault (No confirmation signal from FPD)
F76	FPD radiography communication error
F80	A tube voltage setting value out of the 40 kV to 150 kV range was transmitted from the DR.
F81	A tube current setting value not set for any tube current position for RADspeed fit was transmitted from the DR.
F82	A radiography time setting value out of the 1 msec - 10 msec range was transmitted from the DR.
F83	An invalid tube focal spot was transmitted from the DR.
F84	A tube current time product setting value out of the 0.5 mA to 500 mA range was transmitted from the DR.
F85	An invalid phototimer pickup field was transmitted from the DR.
F86	An invalid film density was transmitted from the DR.
F87	An invalid film sensitivity was transmitted from the DR.
F88	A program code out of the 0 to 432 range was transmitted from the DR.
F89	An invalid technique code was transmitted from the DR.

F8a	An additonal filter number that cannot be selected was transmitted from the DR.